Fitting an Outside Tap in Bradford: Frost Protection

An outdoor tap with a brass handle and hose connector fitted to a red brick house wall

A good outside tap in Bradford needs three things: a double check valve to stop dirty water flowing back into your drinking supply, an isolation valve inside the house so you can turn it off and drain it, and lagging on any exposed pipe. Fit it that way, drain it down before the first frost, and leave the tap open all winter. That is the whole frost protection routine.

Find your situation first

  • You want a new outside tap fitted: read what a good fitting includes, then the cost table.
  • You already have a tap and winter is coming: go straight to the five-step winterising routine.
  • Your outside tap has stopped working in cold weather: read the frozen tap section.
  • Water is spraying from the tap or the pipe through the wall: turn the water off at the isolation valve or stop tap now, then read when to stop and call.
  • Your tap drips all the time: read the causes table.
  • You rent your home: ask your landlord before fitting a new tap.

What can go wrong with an outside tap?

Most outside tap problems come from a short list.

Problem What you will notice Safe to check yourself, or plumber job
Frozen pipe through the wall No water from the tap in cold weather; the pipe feels cold and hard Thaw gently (below); a split pipe is a plumber job
Split tap body or pipe Water spraying when you turn the tap on, often only after a thaw Turn the water off; plumber fixes it
No isolation valve inside You cannot turn the outside tap off without turning off the whole house Plumber fits one; do not leave it like this over winter
No double check valve Nothing visible; dirty water can flow back into your drinking supply Plumber checks and fits one; this is a legal requirement
Dripping tap A steady drip, worse in cold weather; damp on the wall below the tap Safe to check the washer; a seized tap is a plumber job
Hose left connected over winter Water trapped in the hose freezes and splits the tap Safe to fix yourself: disconnect and drain the hose
Exposed pipe with no lagging Bare copper or plastic pipe running along an outside wall Safe to lag yourself; a plumber re-routes it if it keeps freezing

What a good outside tap fitting includes

An outside tap is a small job, but it is still regulated plumbing: it connects your drinking water to the garden. Check that all five of these are in the quote.

  • A double check valve. This stops water flowing backwards from the hose into your drinking supply. A hose left in a bucket or a pond is the classic risk: if the mains pressure drops, dirty water can be drawn back up the hose. The Water Supply (Water Fittings) Regulations 1999 require backflow protection on an outside tap, and for an ordinary garden tap that means a double check valve.
  • An isolation valve inside the house. A small valve on the pipe before it passes through the wall, usually under the kitchen sink. Without one, the tap cannot be drained down for winter, and that is how most outside taps burst.
  • A drain point. A small drain tap on the inside pipework lets the water out of the section between the isolation valve and the outside tap. Either way, the pipe must be able to empty fully.
  • Lagging on exposed pipe. Any pipe outside the warm wall needs waterproof foam lagging, including the short elbow where the pipe leaves the brickwork. That elbow is the most common burst point: a small piece of exposed metal that freezes fast.
  • A frost-free tap, if the position is exposed. A frost-free tap has a long stem, so the valve that shuts the water off sits inside the warm wall rather than in the cold tap body. It costs more, but it is the right choice for a shaded or north-facing wall.

Ask the plumber to show you where the isolation valve is before they leave. You do not need planning permission to fit an outside tap on most properties. If you live in a flat, a listed building, or a new-build still under warranty, check before anyone drills through the wall.

Safe checks, in order: winterising your outside tap

Do these five steps every autumn, before the first frost.

An outdoor tap dripping water in falling snow, with frost on the pipe

  1. Turn off the inside isolation valve. Find the valve on the pipe feeding the outside tap, usually under the kitchen sink, and turn it until it is closed. If it is stiff, do not force it: a seized valve needs a plumber.
  2. Open the outside tap and let it drain. Go outside and open the tap fully. Let every drop run out of the pipe between the valve and the tap.
  3. Open the drain point, if there is one. Some fittings have a small drain tap inside. Open it and let that section empty too, then close it again.
  4. Leave the outside tap open all winter. This is the step people forget. If trapped water freezes, the open tap gives the ice room to expand out of the spout instead of splitting the tap or the pipe.
  5. Fit an insulated tap cover. A padded, waterproof cover over the tap head adds protection against wind chill. It is not a substitute for draining the pipe down: a cover on a full pipe still freezes.

While you are there, disconnect the hose, drain it, and store it indoors. A hose left connected traps water in the tap and freezes solid, which splits the fitting it is attached to.

Your outside tap has already frozen: what to do

A frozen outside tap is not yet a burst tap: the split usually shows only when the ice melts, so thaw it slowly and watch for leaks.

  1. Turn the water off at the inside isolation valve first. If the pipe has split, this keeps the flood small. If there is no isolation valve, turn the water off at the house stop tap.
  2. Open the outside tap. This gives the water somewhere to go as the ice melts, and takes pressure off the pipe.
  3. Warm the pipe slowly. Wrap it in towels soaked in warm water. Start at the tap end and work back towards the house. WaterSafe’s guide to frozen pipes gives the same steps: thaw slowly, never with a naked flame.
  4. Never use direct heat. No blowtorch, no heat gun, and no naked flame. Direct heat can crack the pipe, melt a plastic fitting, and start a fire.
  5. Watch for a split as it thaws. Run a dry cloth along the pipe. If water appears or sprays when you turn the supply back on, turn the water off again and call a plumber. If a pipe has already burst, read our guide to what to do if a pipe bursts first.

If the tap still gives no water after thawing, the freeze may be further back inside the wall. Do not keep forcing the tap handle.

When to stop and call a plumber

Call a plumber now if any of these apply:

  • Water is spraying from the tap, the pipe through the wall, or a joint inside the house.
  • The pipe has split, or water appears as the pipe thaws.
  • There is no isolation valve, so you cannot turn the outside tap off on its own.
  • There is no double check valve, or you are not sure whether one is fitted.
  • The isolation valve is seized and will not turn.
  • Water is coming through a wall, ceiling, or floor near the tap pipework.
  • The tap is seized solid, or the handle turns but nothing happens.
  • You can smell gas. Leave the property first, then call 0800 111 999. Never open the boiler casing; gas work is for a Gas Safe registered engineer only.

For any of these, kitchen plumbing in Bradford covers outside tap fitting, repairs, and frost damage. Call Plumber Bradford Pros on 01274 041977 and say whether the water is off and where the tap is.

If water is spraying and you cannot stop it, call an emergency plumber in Bradford straight away, after turning the water off at the house stop tap if you can do so safely.

What does fitting an outside tap cost?

These are UK guide averages, not this business’s prices. The final cost depends on how far the tap is from the water supply and whether you want a standard or frost-free tap.

Job UK guide average
Fit an outside tap (materials and labour) £120 to £200, average about £160
DIY parts only (tap, pipe, fittings) About £80
Labour time for a full fitting 2 to 4 hours
Extra cost if a burst pipe is found during the job About £330 on average

The figures come from Checkatrade’s tap installation cost guide, last updated June 2026. A tap fitted a long way from the kitchen sink costs more, and a frost-free or hot-and-cold mixer tap costs more than a standard cold-only tap. Ask for the price before work starts, and ask whether the double check valve and the isolation valve are included in the quote.

Fix a dripping outside tap before winter: a tap that drips all winter wastes water, and on a metered supply you pay for every litre.

Outside taps in Bradford homes

Much of Bradford is stone-built terraces and back-to-backs, many with cellars and older copper or lead pipes. The pipe to an outside tap often runs through a cold cellar or along an unheated outside wall, and that is exactly where the first frost bites.

Stop taps in Bradford homes are usually under the kitchen sink, in a downstairs toilet, or under the stairs; in older terraces the stop tap can be in the cellar. Find yours now, and turn it off and on once a year so it does not seize.

Bradford sits on the edge of the Pennines, and the higher streets catch hard frosts early. A tap on a shaded, north-facing wall can stay frozen for days after the rest of the garden has thawed.

Who pays depends on where the problem is. Yorkshire Water is responsible for the mains and the pipes up to your property boundary. You are responsible for the supply pipe from the boundary to your house, including the outside tap. If water is coming up in the street, report it to Yorkshire Water on their freephone Leakline, 0800 57 35 53.

If you rent: fitting a new outside tap means drilling through an outside wall, so ask your landlord or letting agent first. A leaking or frozen outside tap is a repair: tell your landlord straight away.

How to stop the next freeze

  • Drain the tap down every October. Five minutes now saves a burst pipe in January.
  • Leave the tap open all winter, so pressure cannot build up and split the pipe.
  • Disconnect the hose every time you finish with it.
  • Lag every exposed pipe. Check it each autumn: birds and weather pull it loose, and a gap in the lagging is where the pipe freezes.
  • Fix drips before winter: a small job in October, a burst pipe in January.
  • Know where the isolation valve is. Show everyone in the house.

Frequently asked questions

Does an outside tap need a double check valve?

Yes. The Water Supply (Water Fittings) Regulations 1999 require backflow protection on an outside tap, and for an ordinary garden tap that means a double check valve.

How do I winter-proof an outside tap?

Turn off the inside isolation valve, open the outside tap and let it drain, leave the tap open all winter, and fit an insulated tap cover. Disconnect the hose.

Should I leave my outside tap open or closed in winter?

Open. Once the supply is isolated and the pipe is drained, leave the tap open all winter, so any trapped water can expand out of the spout instead of splitting the tap or the pipe.

How much does it cost to fit an outside tap in Bradford?

As a UK guide average, £120 to £200 including materials and labour, about £160 on average (Checkatrade, June 2026). The price depends on how far the tap is from the water supply and whether you choose a standard or frost-free tap.

My outside tap has frozen. What should I do?

Turn the water off at the inside isolation valve, open the outside tap, and thaw the pipe slowly with warm towels, starting at the tap end. Never use a blowtorch or naked flame. If water sprays as it thaws, turn the water off and call a plumber.

Can I fit an outside tap myself?

Only if you have solid plumbing experience and know how to isolate the water supply first. Fitting one means drilling through an exterior wall, fitting a double check valve, and adding an isolation valve inside. Parts cost about £80 as a UK guide average (Checkatrade, June 2026). If you are not sure about the backflow rules, hiring a plumber avoids a leak that costs far more to fix than the fitting.

Plumber Bradford Pros, 164 Dyson Street, Bradford BD9 4DE. Call 01274 041977.

plumber Bradford Pros Team of Experts

Let’s Solve Your Plumbing Problems Today!

Need a trusted plumber in Bradford? We’ve got you covered! Whether it’s a leaking tap, a blocked drain, or a full system installation, we’re ready to help.

Scroll to Top
Call Now